{"id":904,"date":"2026-11-22T02:09:54","date_gmt":"2026-11-21T18:09:54","guid":{"rendered":"http:\/\/www.reaperrscanss.com\/blog\/?p=904"},"modified":"2026-11-22T02:09:54","modified_gmt":"2026-11-21T18:09:54","slug":"how-to-make-a-tubular-rivet-419c-26e756","status":"publish","type":"post","link":"http:\/\/www.reaperrscanss.com\/blog\/2026\/11\/22\/how-to-make-a-tubular-rivet-419c-26e756\/","title":{"rendered":"How to make a tubular rivet?"},"content":{"rendered":"<p>If you\u2019ve ever assembled a metal appliance, a piece of furniture, or a heavy-duty vehicle part, chances are a tubular rivet was holding it all together. For 12 years, I\u2019ve run a small, family-owned tubular rivet supply shop here in Cleveland, Ohio, and I get asked this question at least once a week: How do you make a tubular rivet that\u2019s strong, consistent, and doesn\u2019t fail when it matters? It\u2019s not just stamping metal and calling it a day\u2014there\u2019s a lot of precision, material science, and quality checks that go into every single one. Today, I\u2019m pulling back the curtain on our process, the same one we\u2019ve refined over decades, to make rivets that meet the demands of construction, automotive, aerospace, and every industry in between that relies on permanent, vibration-resistant fasteners. <a href=\"https:\/\/www.liaomet.com\/tubular-rivet\/\">Tubular Rivet<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.liaomet.com\/uploads\/47881\/small\/aluminium-solid-rivetsa2569.jpg\"><\/p>\n<p>First, let\u2019s start with why tubular rivets matter more than solid rivets for so many jobs. Unlike solid rivets, which require a ton of force to deform and need full access to both sides of a material, tubular rivets are hollow, so they collapse on one side when you set them. That makes them perfect for blind applications\u2014think assembling the back of a refrigerator cabinet where you can\u2019t reach the inside, or a trailer frame where one side is exposed only to the road. But that hollow design also means their manufacturing has to be precise; a flaw in the wall thickness or the hole can turn a strong rivet into a failed one. That\u2019s why we never cut corners on raw materials, and we follow a step-by-step process that\u2019s been tested against thousands of field applications.<\/p>\n<p>The first step in making any good tubular rivet is selecting the right raw material. We don\u2019t use just any metal\u2014for most standard applications, we opt for cold-finished steel, which is stronger and more consistent than hot-rolled steel. For industries that need corrosion resistance, like marine equipment or outdoor furniture, we use 300 series stainless steel, and for lightweight jobs, aluminum alloys that won\u2019t add extra weight. The key here is that the material has to be ductile enough to deform when you set it, but strong enough to hold the load. We source our wire from a local steel mill that\u2019s been in business since the 1950s, so we can guarantee every spool meets ASTM standards\u2014no off-spec wire that would snap during forming or break after a year of use. Our typical wire diameter ranges from 1\/32 of an inch to 1\/2 inch, depending on the rivet size we\u2019re making, and we check every spool with a micrometer before it even leaves our loading dock.<\/p>\n<p>Next comes drawing and cutting the wire to length. Cold drawing is how we get the wire to the exact diameter we need, without heating it up (which would soften the metal and ruin its tensile strength). We feed the raw wire through a series of dies, each one slightly smaller, until it reaches our desired gauge. This process also work-hardens the metal a little, adding just the right amount of strength without making it too brittle. Once the wire is at the correct diameter, we cut it into blanks\u2014small, uniform lengths of wire that will become the rivet body. This is where consistency is non-negotiable. We use automated cutting machines, not manual shears, because manual cuts can leave burrs or uneven ends, which would cause the rivet to misalign during setting. Each blank is cut to within 0.005 inches of its target length, and we discard any that don\u2019t meet that tolerance. We also deburr every blank right after cutting, because even a tiny metal shard left on the end can create a gap in the joint when the rivet is installed.<\/p>\n<p>The third step is punching the central hole. This is what turns a solid metal blank into a tubular rivet, and it\u2019s the most delicate part of the process. We mount each blank in a precision punch press, where a hardened steel punch drills a hole all the way through the center. The punch has to be sharp and aligned perfectly with the center of the blank\u2014if it\u2019s off by even 0.003 inches, the rivet\u2019s wall thickness will be uneven, leading to a weak spot that can split when set. We use tool steel punches that we regrind every 5,000 uses, because a dull punch will create a ragged hole that compromises the rivet\u2019s integrity. For rivets with larger holes (like semi-tubular rivets, which are a slight variation we make for high-load applications), we adjust the punch pressure to ensure the hole is smooth and free of deformation. Right after punching, we run every blank through a visual inspection station, where a camera checks for hole diameter, wall thickness, and any cracks around the hole. Any blank that doesn\u2019t pass goes straight into the scrap bin\u2014we don\u2019t risk sending a bad rivet to a customer, no matter how small the order.<\/p>\n<p>Once the blanks are punched, we form the rivet head. The head is the part that bears against the surface of the material you\u2019re fastening, so it has to be flat, uniform, and the right size to distribute load evenly. We use cold heading machines for this step\u2014these machines compress one end of the blank into a shape, usually round or flat, depending on the rivet type. Cold heading is better than hot forming here because it doesn\u2019t alter the metal\u2019s grain structure; the metal\u2019s grain stays aligned, which makes the head stronger and more resistant to shearing. We offer two common head styles: round head for general construction, and countersunk head for flush surfaces where the rivet won\u2019t catch on things. Each head is formed to a tight tolerance\u2014we make sure the head height is within 0.01 inches of our specs, so when customers install them, the head doesn\u2019t sit too high and cause a problem. After heading, we do a second quality check, weighing each rivet to make sure it has the right amount of material. A light rivet would be too thin, and a heavy one would have excess material that would make setting difficult.<\/p>\n<p>The final shaping step is what gives the tubular rivet its hollow profile, and this is where we adapt based on the customer\u2019s needs. For standard tubular rivets, we expand the end opposite the head slightly to create a bell shape, which helps it deform uniformly during setting. For blind rivets, which are a type of tubular rivet used when access is only on one side, we add a mandrel hole later, but let\u2019s stick to our standard solid tubular rivet for now. Once all shaping is done, we clean the rivets to remove any oil or metal dust from the forming process. We use a mild alkaline wash that\u2019s safe for the metals we work with, followed by a rinse and a light coating of anti-corrosive wax if the rivets will be used outdoors. We don\u2019t use heavy plating unless a customer requests it, because plating can add extra thickness that makes installation harder. For customers that do need plating, like zinc plating for extra rust protection, we work with a local plating shop that meets our environmental standards, so we can guarantee the finish will last as long as the rivet itself.<\/p>\n<p>Wait, let\u2019s also talk about a step that a lot of small suppliers skip, but we swear by: testing every batch. We don\u2019t just make rivets and ship them\u2014we pull 10 rivets from every production run and test their pull-out strength. That means clamping them between two steel plates, using a hydraulic press to set them, then pulling until the head breaks or the rivet pulls through the material. If even one rivet in the batch fails, we scrap the entire run and go back to check our process. Last year, we caught a bad batch of steel wire right before we started production\u2014our raw material check would have missed it if we didn\u2019t test the final product, and that would have cost a local construction company thousands in rework. That\u2019s the kind of care that comes from being in this business for 12 years; we know that a rivet that fails isn\u2019t just a bad part, it can cause a job to shut down, or worse, a piece of equipment to fall apart.<\/p>\n<p>Now, you might be wondering how this process compares to other fasteners. Why would someone choose a tubular rivet over a bolt or a screw? Bolts require threading, which adds cost, and screws can pull out of soft materials or vibrate loose over time. Tubular rivets, when set correctly, create a permanent joint that doesn\u2019t loosen, even with constant vibration\u2014perfect for heavy machinery, truck frames, or playground equipment that gets knocked around. The process of making them is also more efficient for high volume runs, which is why we can offer competitive pricing for bulk orders, without sacrificing quality.<\/p>\n<p>We also make custom tubular rivets for customers that can\u2019t find a standard size. A lot of our work comes from small manufacturers who have a unique assembly line that needs a rivet with a 3\/16 inch diameter, a countersunk head, and a hole drilled at a slight angle\u2014something off the shelf won\u2019t work. For those orders, we adjust our process on the fly, using custom dies and tooling, and work with the customer to get every spec just right. That\u2019s another reason we\u2019ve stayed in business; we\u2019re not just a supplier, we\u2019re a partner for other businesses that need fasteners they can trust.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.liaomet.com\/uploads\/47881\/small\/semi-tubular-rivets693f3.jpg\"><\/p>\n<p>If you\u2019re working on a project that needs tubular rivets\u2014whether it\u2019s a small home renovation, a commercial construction job, or a custom equipment build\u2014our team can help. We stock standard sizes in steel, stainless steel, and aluminum for immediate shipment, and we can make custom orders in as little as three days. We prioritize quality at every step, from raw material sourcing to final testing, because we know that the rivets we make are holding your work together. If you\u2019re looking to place an order, or have questions about the right rivet for your application, reach out to our team to discuss your needs. We\u2019re here to help you find the perfect fastener, no matter how big or small the job.<\/p>\n<p><a href=\"https:\/\/www.liaomet.com\/tubular-rivet\/\">Tubular Rivet<\/a> References<br \/>\nASM International. (2008). Forging and Forming of Metals. ASM Handbook, Volume 14A.<br \/>\nASTM International. (2022). Standard Specification for Steel Rivets, Carbon and Alloy, Cold-Formed. ASTM F115-22.<br \/>\nThe Fabricator. (2021). Understanding Tubular Rivets: Manufacturing and Applications. The FABRICATOR Magazine.<\/p>\n<hr>\n<p><a href=\"https:\/\/www.liaomet.com\/\">Wenzhou Liao Fasteners Co., Ltd.<\/a><br \/>As one of the most professional tubular rivet manufacturers and suppliers in China, we also support customized service. Welcome to wholesale high quality tubular rivet in stock here from our factory. If you have any enquiry about cooperation, please feel free to email us.<br \/>Address: No.93 Liaodong Road, Liao Subdistrict, Ouhai District, Wenzhou City, Zhejiang Province, China<br \/>E-mail: zhengyue1687@163.com<br \/>WebSite: <a href=\"https:\/\/www.liaomet.com\/\">https:\/\/www.liaomet.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>If you\u2019ve ever assembled a metal appliance, a piece of furniture, or a heavy-duty vehicle part, &hellip; <a title=\"How to make a tubular rivet?\" class=\"hm-read-more\" href=\"http:\/\/www.reaperrscanss.com\/blog\/2026\/11\/22\/how-to-make-a-tubular-rivet-419c-26e756\/\"><span class=\"screen-reader-text\">How to make a tubular rivet?<\/span>Read more<\/a><\/p>\n","protected":false},"author":449,"featured_media":904,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[867],"class_list":["post-904","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-tubular-rivet-467b-2812bf"],"_links":{"self":[{"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/posts\/904","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/users\/449"}],"replies":[{"embeddable":true,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/comments?post=904"}],"version-history":[{"count":0,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/posts\/904\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/posts\/904"}],"wp:attachment":[{"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/media?parent=904"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/categories?post=904"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.reaperrscanss.com\/blog\/wp-json\/wp\/v2\/tags?post=904"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}